Home>Products>Serial ATA I/II Series

eSATA –150 1External +1 Internal Low Profile PCI Adapter Chipset: Silicon Image One special SATA II external connector (eSATA) Provides 2 Brackets to Support Low profile PCI and Regular size PCI in one card 48 bits LBA can Break Capacity-Limit to Support HDD larger than 137GB Dual high speed Serial ATA interface ports, each supporting 1st generation Serial ATA data rates 1.5Gb/s Fully compliant with Serial ATA 1.0a specifications Two Pin header on board for LED connection Supports Spread Spectrum in receiver Independent 256-byte FIFOs (32 bit * 64 deep) per Serial ATA channel for host reads and writes Compliant with PCI Specification, revision 2.2 Integrated PCI DMA engines 32 bit, 33/66MHz fully compliant PCI host interface  OS: Windows 98SE / ME / NT4.0 / 2000 / XP / 2003 / Vista RAID eSATA-150 2 External eSATA + 2 Internal + 2A5V Bracket Power PCI Host Chipset: Silicon Image Two eSATA shielded and durable external connectors 48 bits LBA can Break Capacity-Limit to Support HDD larger than 137GB Sufficient power current 2000mA to supply 5V External Storage Hot-plug capability Four high speed Native Serial ATA interface ports, each supporting 1st generation Serial ATA data rates 1.5Gb/s Support RAID 0(Stripping), RAID 1(Mirroring), RAID 0+1 (Mirrored-Stripping), RAID 1+S (Mirrored-sparing) mode Fully compliant with Serial ATA 1.5G specifications Supports ATAPI devices Supports Spread Spectrum in receiver Independent 256-byte FIFOs (32 bit * 64 deep) per Serial ATA channel for host reads and writes Compliant with PCI Specification, revision 2.3 Four Pin header on board for LED connection Integrated PCI DMA engines 32 bit, 33/66MHz fully compliant PCI host interface USB-like Connector on board to provide 2000mA / 5V DC power output for External Mobile Devices Acts as NON-RAID when BIOS not configured RAID OS: Windows 98SE / ME / NT4.0 / 2000 / XP / 2003 / Vista Raid5 SATA II – 3Gbps 4Ports (1External eSATA + 3 Internal) Low Profile PCI Host Chipset: Silicon Image SATA II External Connector (eSATA) on External port  Provides 2 Brackets to Support Low profile PCI and Regular size PCI in one card Compliant with PCI Specification, revision 2.3 Supports 66 MHz PCI with 32-bit data Internal application interface multiplexed to 4 ports All registers appear in unified memory space Full-chip command completion status accessible with single PCI burst access I/O port access to register space Low Profile PCI form factor Fully compliant with Serial ATA 1.0a and Serial ATA II Extensions to Serial ATA 1.0a Specifications revision 1.1 Hot-plug capability Supports Serial ATA Generation 2 transfer rate of 3.0 Gb/s Supports SATA II First-party DMA commands for Native Command Queuing (NCQ) Supports Serial ATA II Port Multiplier 1.0 Specifications revision 1.1 Plesiochronous, Single PLL architecture, 1 PLL for 4 ports Supports four independent Serial ATA channels Independent Link, Transport, data FIFO, command fetch, scatter/gather, and command execution 31 Commands and Scatter/Gather Tables per Port Supports bootable drive Four Pin header on board for LED connection Support JBOD, RAID 0(Stripping), RAID 1(Mirroring), RAID 0+1 (Mirrored-Stripping), RAID 5(Distributed Parity RAID) mode OS: Windows 98SE / ME / NT4.0 / 2000 / XP / 2003 / Vista RAID5 eSATA-150 External 4Ports PCI Host Chipset: Silicon Image Four shielded and durable eSATA external connectors 48 bits LBA can Break Capacity-Limit to Support HDD larger than 137GB Four high speed Serial ATA interface ports, each supporting 1st generation Serial ATA data rates 1.5Gb/s Hot-plug capability Fully compliant with Serial ATA 1.5G specifications Support JBOD, RAID 0(Stripping), RAID 1(Mirroring), RAID 0+1 (Mirrored-Stripping), RAID 5(Distributed Parity RAID) mode Supports ATAPI commands Supports Spread Spectrum in receiver Independent 256-byte FIFOs (32 bit * 64 deep) per Serial ATA channel for host reads and writes  Compliant with PCI Specification, revision 2.2 Integrated PCI DMA engines Four Pin header on board for LED connection 32 bit, 33/66MHz fully compliant PCI host interface OS: Windows 98SE / ME / NT4.0 / 2000 / XP / 2003 / Vista USB 2.0(NEC) + eSATA-150 Combo 7Ports PCI Host Adapter Chipset : NEC / Silicon Image Provides Five USB2.0 / USB1.1 ports ( 3 External + 2 Internal) Have USB Type A downtream connector and USB 5Pin Pin header both on board Compliant with Universal Serial Bus Specification Revision 2.0 (Data Rate 1.5/12/480 Mbps) Compliant with Open Host Controller Interface Specification for USB Rev 1.0a Compliant with Enhanced Host Controller Interface Specification for USB Rev 0.95 All USB ports can handle high-speed (480 Mbps), full-speed (12 Mbps), and low-speed (1.5 Mbps) transaction Compliant with PCI Specification, revision 2.2 32 bit, 33MHz fully compliant PCI host interface Integrated PCI DMA engine OS: Windows 98SE / ME / NT4.0 / 2000 / XP / 2003 / Vista SATA-II (1 TO 5) Port Multiplier   General Chipset: Silicon Image Compliant with SATA II external specification Support hot plug and extended (48 bit LBA) drive capability. Supports SATA-II speed of 3Gbps Multiplier 1 to-5 native SATA II Port Multiplier Provides an eSATA host and 5 SATA device connectors Advanced data aggregation architecture for ultra-fast read and write operations with FIS-based High-speed, native SATA connection to host and device Host and device status and activity LEDs Full support for FIS-based switching and command-based switching SATA host controllers. Supports 1.5Gbps and 3.0Gbps with auto-negotiation. Provides link and activity LED connectors. OS: Windows 2000 / 2003 / XP / Vista

SATA-II (1 TO 5) Port Multiplier General Chipset: Silicon Image Compliant with SATA II external specification Support hot plug and extended (48 bit LBA) drive capability. Supports SATA-II speed of 3Gbps Multiplier 1 to-5 native SATA II Port Multiplier Provides an eSATA host and 5 SATA device connectors Advanced data aggregation architecture for ultra-fast read and write operations with FIS-based High-speed, native SATA connection to host and device Host and device status and activity LEDs Full support for FIS-based switching and command-based switching SATA host controllers. Supports 1.5Gbps and 3.0Gbps with auto-negotiation. Provides link and activity LED connectors. OS: Windows 2000 / 2003 / XP / Vista Mini SATA-II (1 TO 5) Port Multiplier Hot Plug support Supports Asynchronous Notification SATA Port Multiplier spec. complaint Supports PM aware hosts and non-PM aware eSATA signal level support (1m and 2m PH compliant) Compatible with NCQ SATA drive Advanced data aggregation architecture for ultra-fast read and write operations with FIS-based switching controllers 1.5Gpbs or 3Gpbs link rate with auto-negotiation Support JBOD, RAID 0, RAID 1, RAID 0+1, RAID5 OS: Windows 2000 / 2003 / XP / Vista FireWire 800 (IEEE 1394b) + USB 2.0 Combo for all SATA and SATA II Hard Drives Chipset: Oxford, TI FireWire 1394b Supports FireWire 800 and FireWire 400 Tow External 1394b port USB 2.0 Supports High-speed USB2.0 480Mbps compatibility with USB1.1 One External USB 2.0 port SATA Operates at 1.5GHz, assuring a disk interface data rate of 150Mbytes/sec. Supports SATA II port multiplier specification Tow Internal SATA port RAID Supports RAID 0 function Striping - allows two SATA disks to appear as a single higher speed disk, by sharing the load between two disks. Spanning - allows two drives to appear as one to the host machine OS: Windows 2000 / 2003 / XP / Vista

SATA II Multi-Lane External Cable -1M/2M Multi-lane SATA (serial ATA) 4x cable is the one of the high performance serial bus, extended to 2.0 meter (6.0 feet) Capable of transfer 4x independent SATA devices up to 3.0Gbps per channel. Four individual channels in 1 Superior reliability Ease-of-installation cable meets and exceeding SATA II Requirements with screws type connectors and heavy external shielding cable, Infiniband (Multilane SATA) cable provide a data path with free of RFI, EMI

Raid5 SATA II 4Ports PCI-X Host Card Jack Chipset: Silicon Image Compliant with PCI Specification, revision 2.2. Integrated PCI DMA engines. 64 bit, 133MHz fully compliant PCI host interface. Four high speed Serial ATA interface ports, each supporting 1st generation & 2 nd generation Serial ATA data rates 1.5Gbps/ 3Gbps. Provides RAID 0 (Stripping) to greatly increase the performance of data transfer by simultaneously writing data to 2 drives. Provides RAID 1 (Mirroring) to protect the data from a disk failure by writing identical data on 2 drives. RAID 0+1 (Mirrored-Stripping) combine both Striping and Mirroring technologies to provide both the performance enhancements that come from Striping and the data availability and integrity that comes from Mirroring. Provides RAID 5 (Block-level stripping with distributed parity), stripes both data and parity information across three or more drivers. Fully compliant with Serial ATA specifications. Supports Spread Spectrum in receiver. Supports Independent four External Ports OS: Windows 2000 / XP / NT4.0 / 2003 / Vista

Raid5 SATA II 4 Ports PCI-X Low Profile Host Card Chipset: Silicon Image Compliant with PCI Specification, revision 2.2. Integrated PCI DMA engines. 64 bit, 133MHz fully compliant PCI host interface. Four high speed Serial ATA interface ports, each supporting 1st generation & 2nd generation Serial ATA data rates 1.5Gbps/ 3Gbps. Provides RAID 0 (Stripping) to greatly increase the performance of data transfer by simultaneously writing data to 2 drives. Provides RAID 1 (Mirroring) to protect the data from a disk failure by writing identical data on 2 drives. RAID 0+1 (Mirrored-Stripping) combine both Striping and Mirroring technologies to provide both the performance enhancements that come from Striping and the data availability and integrity that comes from Mirroring. Provides RAID 5 (Block-level stripping with distributed parity), stripes both data and parity information across three or more drivers. Fully compliant with Serial ATA specifications. Supports Spread Spectrum in receiver. Supports Independent four Internal Ports OS: Windows 2000 / XP / NT4.0 / 2003 / Vista

SATA II (X4) External Adapters Provides one 4-channel (x4) infinite Band Connector Ideal to convert internal 4 ports to External 4 ports Supports up to 3Gb/s SATAII Data Transfer Rate 4 External LED Activity indicators for each Channels Supports Host(PC or Server)and Device (Subsystem or Enclosure)External converting OS: Windows 2000 / XP / NT4.0 / 2003 / Vista

SATA II (X4) External Adapters Provides one 4-channel (x4) infinite Band Connector Ideal to convert internal 4 ports to External 4 ports Supports up to 3Gb/s SATAII Data Transfer Rate 4 External LED Activity indicators for each Channels Supports Host(PC or Server)and Device (Subsystem or Enclosure)External converting OS: Windows 2000 / XP / NT4.0 / 2003 / Vista

2-Port Serial ATA PCI Card Chipset: Silicon Image One (7 Pin+15 Pin) external and one (7 Pin) internal ports Supports ATA RAID 0,1 Compliant with PCI Specification, revision 2.2 Provides External Power Supports data transfer rates up to 150 MB/sec and hard disk drive larger than 137 GB OS: Windows 98SE / ME / NT4.0 / 2000 / XP / 2003 / Vista

2-Port SATA in 3.5" Bay Chipset: Silicon Image Standalone PCI to Serial ATA host controller Compliant with PCI Specification, revision 2.2 Compliant with PCI IDE Controller Specification, revision 1.0. Compliant with Programming Interface for Bus Master IDE Controller, revision 1.0 Driver support for Win9x, WinME, NT4, Win2K, XP Supports the Microsoft driver for generic IDE operations and Intel bus master DMA operations Supports 66 MHz PCI with 32-bit data and bus master operations Compliant with Serial ATA 1.0 specifications Supports two independent Serial ATA channels Supports Serial ATA Generation 1 transfer rate of 1.5Gb/s. OS: Windows 98SE / ME / NT4 / 2000 / XP / Vista

2 Port Serial ATA Card Chipset: Silicon Image Two independent Serial ATA channels to support one Serial ATA device on each channel Supports specific BIOS and driver for RAID level 0 (Striping), RAID level 1 (Mirroring) Drive Types: Serial ATA hard drive Backward compatible with Ultra DMA 133/100/66/33 (parallel) drives (IDE to Serial ATA converter required for parallel ATA drives and ATAPI devices.) Supports 32-bit, 33 or 66 MHz PCI bus Compliant with 32-bit PCI bus version 2.2 Supports Windows 98SE / ME / 2000 / XP / NT4.0 / 2003 / Vista Supports Plug and Play function under Windows 2000/XP

4 Port Serial ATA Card Four independent Serial ATA channels to support one Serial ATA device on each channel   Supports specific BIOS and driver for RAID level 0 (Striping), RAID level 1 (Mirroring) and RAID level 0+1(Striping and Mirroring) functions Drive Types: Serial ATA hard drive Backward compatible with Ultra DMA 133/100/66/33 (parallel) drives (IDE to Serial ATA converter required for parallel ATA drives and ATAPI devices.) Supports 32-bit, 33 or 66 MHz PCI bus Compliant with 32-bit PCI bus version 2.2 Supports Plug and Play function under Windows 2000/XP Supports Windows 98SE / ME / 2000 / XP / NT4.0 / 2003 / Vista

IDE To SATA Adaptor Chipset: Silicon Image Compliant with Serial ATA 1.0 specification Data transfer rate up to 1.5 Gb/s Supports Ultra ATA 66 or 100 or 133 IDE Hard Disk Drive OS: Windows 98SE / ME / NT4.0 / 2000 / XP / 2003 / Vista

Mini Vertical Bridge Board for SATA Device to IDE MotherBoard Supports any type of SATA Device (DVD, DVD-RAM, MO, CD-ROM, CD-RW, Hard Disk, ……) 48 bits LBA can Break Capacity-Limit to Support HDD larger than 137GB Mini Board size (75mm x 26mm), No space wasted Compliant with Serial ATA 1.0a specifications Supports Spread Spectrum in receiver    Compliant with ATA specifications   Compatible with Ultra ATA 133 / 100 / 66 / 33 100% hardware bridge converter to support PC, MAC and Linux environment OS: Windows 98SE / ME / NT4.0 / 2000 / XP / 2003 / Vista 2-Port Serial ATA CardBus Adaptor Fully compliant with Serial ATA 1.0 specifications Supports hard disk drive larger than 137 GB Independent 256-byte FIFOs per channel for host reads and writes Supports Spread Spectrum in receiver Plug and Play OS: Windows 98SE / ME / 2000 / XP / 2003 / Vista